Skip to main content
Table of Contents

DUO Device Overview

Assemble your DUO

Follow our simple process to assemble your DUO stethoscope with the earpieces.

Plug the DUO Earpiece into the 3.5 mm audio port at the base of the DUO and tighten the threads. 

Alternatively, you can choose to use wired headphones instead of the earpiece. To assemble with wired headphones, please follow the same assembly process for stethoscope earpieces. 

You can also use the DUO as a hand-held device to visualize the phonocardiogram (PCG) and single-lead electrocardiogram (ECG). 

Power On/Off

Screen_Shot_2021-08-13_at_4.09.48_PM.png

Power ON

Press and hold down the center button for 1 second to power on your DUO. Once the device is on, you will see a ring of lights circling around the button and a blinking white light. Your device is now ready to pair with the Eko App and be used on a patient.

Power Off

To power off, press and hold down the center button for 2 seconds. Once the device is off, the LED lights will disappear. 

Standby Mode

The DUO has a 5 minute standby mode to conserve battery life. The white light will disappear when the DUO goes into standby mode. To power the device back ON, push the toggle to the OFF and ON position. The white blinking light will appear to indicate the device is ON. 

Adjust the Volume

DUO’s sound level can be amplified in 12 increments up to 32X amplification of an acoustic stethoscope when listening with the stethoscope earpieces. Change the volume level by clicking the top and bottom section of the volume button located on the side of DUO. You will notice that the LED lights will flash when adjusting the volume. 

If you are using headphones to listen to the sounds, please adjust your phone’s volume to change the DUO’s volume. 

Charge the DUO

The DUO can last up to 10 hours of continuous use with a full charge. To charge your DUO, it must be properly placed on the wireless charging pad.

First, connect the charging pad to the power source using the included USB charging cable and power adaptor. You will notice an orange light illuminate at the top of the charging pad once it is plugged in.

Place your DUO on the charging pad with the center button facing you. You will immediately see the LED lights flash and circle around the center button. This is signaling that the device is charging. When fully charged, the lights will stop flashing.

When fully charged, the DUO lasts up to 1 year of battery life with the device on standby. We recommend turning the device OFF between each use to maximize battery time.

Note: DUO will not operate or connect to the Eko app while charging.

Screen_Shot_2021-08-13_at_4.12.51_PM.png

 

Clean the DUO Device 

The DUO should be cleaned between each patient use. Eko recommends cleaning the DUO with 70% isopropyl alcohol wipes or solution. Note: DO NOT immerse the device in any liquid or subject it to any high-pressure/autoclave sterilization processes.

Change your audio filters

To change the filter settings on your DUO, turn the device on by pressing and holding the center button for two seconds. 

Once the DUO is on, you can change the filter settings by pressing the center button three times quickly, in succession. This will allow you to switch between the four filter options. You will notice that the light will switch positions as you switch audio filters. 

The four filter options and corresponding LED light positions are (see image below):

  1. Diaphragm (default) mode (heart sounds)

  2. Bellmode (heart and bowel sounds)
  3. Midrange mode (heart and some lung sounds)
  4. Extended mode(heart and lung sounds)

Screen_Shot_2021-08-13_at_4.13.56_PM.png

Another way to change the audio filters is through Settings in the Eko App. Please visit our Using Software section for more information. 

Was this article helpful?

5 out of 5 found this helpful

Have more questions?

Looking for something different?